AVR 7200 OM 1/27/03 4:46 PM Page 13
AVR7200 harman/kardon
MAIN REMOTE CONTROL FUNCTIONSMAIN REMOTE CONTROL FUNCTIONS
L Preset Up/Down Button: When the tuner is in Mute Button: Press this button to momentarilyspeaker configuration. When a DTS source is not in
use, press this button to scroll through the stations silence the AVR 7200 or TV set being controlled,use, this button has no function. (See page 29 for the
programmed into the AVR 7200Os memory.depending on which device has been selected.available DTS digital options.)
M Tuning Up/Down Button: When the tuner is AM/FM Tuner Select: Press this button to select Dolby Mode Select Button: This button is used
in use, this button will tune up or down through thethe AVR 7200Os tuner as the listening choice. Pressingto select from the available Dolby Surround modes.
selected frequency band. If the Tuning Mode Buttonthis button when the tuner is already in use will selectEach press of this button will select one of the Dolby
B^ has been pressed so that AUTO appears inbetween the AM and FM bands.Pro Logic II modes or Dolby 3 Stereo. When a Dolby
the Lower Display Line B and the AUTO IndicatorDigital-encoded source is in use, the Dolby Digital
Channel Up/Down Selector: This button has no
J lights, pressing either button will cause the tuner tomode may also be selected. (See page 29 for the
function when the AVR is being controlled, but when
seek the next station with acceptable signal strength foravailable Dolby surround mode options.)
programmed for use with a VCR, TV, cable box, satel-
quality reception.When MANUAL appears in thelite receiver or other similar product it will change the 6-Channel/8-Channel Input Select: Press this
Lower Display Line B and the AUTO Indicator J
channel up or down. See pages 38 � 47 for morebutton to select the device connected to the 6- or 8-
goes out, pressing this button will tune stations in single-
information on programming the remote.Channel Direct Inputs34. (See page 28 for more
step increments. (See page 32 for more information.)
Delay Select Button: Press this button to begin information.)
N Disc Skip Button: This button has no direct
the process for setting the delay times used by the SPL Select Button: This button activates the
function for the AVR 7200 but may be used to
AVR 7200 when processing surround sound. AfterEzSet function to quickly and accurately calibrate the
change the disc in a CD or DVD changer when the
remote is programmed for that type of device.pressing this button, the delay times are entered byAVR 7200Os output levels. When the button is pressed
pressing the Set Button F and then the ?/¤you will then need to select between automatic EzSet
O Program Button: This button is used to beginNavigation Button n to change the setting.operation or using the remote as a manual SPL meter
the process of programming the remote. Press and holdPress the Set Button F again to complete theby pressing the ?/¤ Navigation Button n until
this button for three seconds to place the remote in theprocess. (See page 23 for more information on your choice appears in the remoteOs LCD display.
programming mode. Once the red LED under the Setsetting delay times.)Press the Set Button F to enter the setting, and
Button F lights, release the button.You may thenthen follow the instructions as displayed in the LCD
Speaker Select Button: Press this button to
select from the desired option. (See pages 38 � 47 fordisplay. (For complete information, see page 24.)
more information on configuring the remote.)begin the process of configuring the AVR 7200Os
bass management system. Then press the ?/¤ EzSet Microphone Sensor: The microphone
P Light Button: Press this button to activate theNavigation Button n to select the channel yousensor that is used by the EzSet system is behind the
remoteOs backlight for ease of use in darkened rooms.wish to set up. Press the Set Button F and thenthree slots at the top of the remote control. When
select another channel to configure. When all adjust-using EzSet to calibrate the AVR 7200 be certain that
QMultiroom: Press this button to activate the multi-
ments have been completed, press the Set Buttonthe slots are not covered. (See page 24 for more
room system or to begin the process of changing the
F twice to exit the settings and return to normalinformation on using EzSet.)
input or volume level for the second zone. (See page
36 for more information on the multiroom system.)operation. (See page 21 for more information on- Lens: The infrared emitters behind the plastic
speaker setup.)
lens at the top of the remote communicate the remote
Macro Buttons: Press these buttons to store or
Memory Button: Press this button to enter a codes to the AVR 7200. Be certain that the lens is not
recall a OMacro�, which is a preprogrammed sequence
radio station into the AVR 7200Os preset memory.covered when using the remote, and point the lens
of commands stored in the remote. (See page 41 forOnce PRESET MEMORY flashes in the toward the AVR for best results. In learning mode, the
more information on macros.)
Lower Display Line B and the Memory Indicatorremote receives IR codes to be learned through a
Sleep Button: Press this button to place the unitG lights, you have five seconds to enter a presetsensor behind the lens.
in the Sleep mode. After the time shown in the display,memory location using the Numeric Keys A.NOTE: DO NOT remove the rubber plug that is supplied
the AVR 7200 will automatically go into the Standby(See page 32 for more information.)
to cover the jack on the upper right side of the remote.
mode. Each press of the button changes the time until
Stereo Mode Select Button: Press this buttonThe jack is not active and is reserved for future use.
turn-off in the following order:
to select a stereo listening mode. The first press of the9080706050
minminminminminbutton places the AVR 7200 in a true, two-channel,
40302010left/right Stereo mode with no surround processing.OFF
minminminmin
The next press selects either five-channel Stereo or
Night Mode Button: Press this button to acti-seven-channel Stereo, depending on the speaker
configuration.
vate the Night mode.This mode is available in specially
encoded Dolby Digital sources, and it preserves DTS Neo:6 Mode Select Button: Press this
dialogue (center channel) intelligibility at low volumebutton to select a DTS Neo:6 mode. (See page 29
levels.for the available DTS Neo:6 options.)
OSD Button: Press this button to activate the
DTS Digital Mode Select Button: When a
On-Screen Display (OSD) system used to set up orDTS-encoded digital source is playing, each press of
adjust the AVR 7200Os parameters.this button will scroll through the available DTS modes.
The specific choice of modes will vary according to
the type of encoding on the disc and your systemOs
MAIN REMOTE CONTROL FUNCTIONS 13MAIN REMOTE CONTROL FUNCTIONS 13
13 |
ACEC
